Javascript required
Skip to content Skip to sidebar Skip to footer
Home / Computer App That Can Draw Arduino 101 Information

Computer App That Can Draw Arduino 101 Information

Blink

This example shows the simplest thing you can do with an Arduino to see physical output: it blinks the on-board LED.

Hardware Required

  • Arduino Board

optional

  • LED

  • 220 ohm resistor

Circuit

This example uses the built-in LED that most Arduino boards have. This LED is connected to a digital pin and its number may vary from board type to board type. To make your life easier, we have a constant that is specified in every board descriptor file. This constant is LED_BUILTIN and allows you to control the built-in LED easily. Here is the correspondence between the constant and the digital pin.

  • D13 - 101

  • D13 - Due

  • D1 - Gemma

  • D13 - Intel Edison

  • D13 - Intel Galileo Gen2

  • D13 - Leonardo and Micro

  • D13 - LilyPad

  • D13 - LilyPad USB

  • D13 - MEGA2560

  • D13 - Mini

  • D6 - MKR1000

  • D13 - Nano

  • D13 - Pro

  • D13 - Pro Mini

  • D13 - UNO

  • D13 - Yún

  • D13 - Zero

If you want to lit an external LED with this sketch, you need to build this circuit, where you connect one end of the resistor to the digital pin correspondent to the LED_BUILTIN constant. Connect the long leg of the LED (the positive leg, called the anode) to the other end of the resistor. Connect the short leg of the LED (the negative leg, called the cathode) to the GND. In the diagram below we show an UNO board that has D13 as the LED_BUILTIN value.

The value of the resistor in series with the LED may be of a different value than 220 ohm; the LED will lit up also with values up to 1K ohm.

circuit

Schematic

schematic

Code

After you build the circuit plug your Arduino board into your computer, start the Arduino Software (IDE) and enter the code below. You may also load it from the menu File/Examples/01.Basics/Blink . The first thing you do is to initialize LED_BUILTIN pin as an output pin with the line

pinMode(LED_BUILTIN, OUTPUT);

In the main loop, you turn the LED on with the line:

digitalWrite(LED_BUILTIN, HIGH);

This supplies 5 volts to the LED anode. That creates a voltage difference across the pins of the LED, and lights it up. Then you turn it off with the line:

digitalWrite(LED_BUILTIN, LOW);

That takes the LED_BUILTIN pin back to 0 volts, and turns the LED off. In between the on and the off, you want enough time for a person to see the change, so the delay() commands tell the board to do nothing for 1000 milliseconds, or one second. When you use the delay() command, nothing else happens for that amount of time. Once you've understood the basic examples, check out the BlinkWithoutDelay example to learn how to create a delay while doing other things.

Once you've understood this example, check out the DigitalReadSerial example to learn how read a switch connected to the board.

See Also

  • setup()

  • loop()

  • pinMode()

  • digitalWrite()

  • delay()

  • AnalogReadSerial - Read a potentiometer, print its state out to the Arduino Serial Monitor.

  • BareMinimum - The bare minimum of code needed to start an Arduino sketch.

  • DigitalReadSerial - Read a switch, print the state out to the Arduino Serial Monitor.

  • Fade - Demonstrates the use of analog output to fade an LED.

  • ReadAnalogVoltage - Reads an analog input and prints the voltage to the serial monitor.

Last revision 2015/07/28 by SM

Last revision

February 05, 2018, at 08:43 PM

Computer App That Can Draw Arduino 101 Information

Source: https://www.arduino.cc/en/Tutorial/BuiltInExamples/Blink/